精品国产sm全部网站免费_日韩精品毛片_推荐高清免费不卡网站_亚洲无码人成电影在线观看_一本伊大人香蕉久久網手機_福利视频你懂得_亚洲欧美曰韩在线_成年男女免费网站点播_成年人播放一级片高清_亚洲视频在线视频

    The ME4086 is a complete battery charger controller for one (4.2V) or three (12.6V) cell lithium-ion battery. The ME4086 provides a small, simple and efficient solution to fast charge Li-ion battery. The

ME4086 built in anti current backward function, so the application does not need the blocking diode. An external sense resistor sets the charge current with high accuracy.

    An internal resistor divider and precision reference set the final float voltage to one (4.2V) or three (12.6V) cell with ±1% accuracy. When the input supply is removed, the ME4086 automatically enters a low

current sleep mode, dropping the battery drain current to 3μA.After the charge cycle ends, If the battery voltage drops below one (4.1V) or three (12.2V) cell, a new charge cycle will automatically begin.

    ME4086是一款適用于單電池（4.2V）或三電池（12.6V）鋰離子電池的完整電池充電器控制器。ME4086為鋰離子電池的快速充電提供了一種小型、簡單、高效的解決方案。ME4086內置反電流反向功能，因此應用不需要阻塞二極管。外部感測電阻器以高精度設置充電電流。

    內部電阻分壓器和精度基準將最終浮動電壓設置為一個（4.2V）或三個（12.6V）單元，精度為±1%。當輸入電源斷開時，ME4086自動進入低電流睡眠模式，將電池漏電流降至3μa。充電周期結束后，如果電池電壓降至一個（4.1V）或三個（12.2V）電池以下，將自動開始新的充電周期。 

ME4086 Features（特性）：

Input Supply Range：

  One-cell：4.7V~16V

  Three-cell：14V~22V

Maximum input voltage：24V

Built in anti current backward function

High Efficiency Current Mode PWM Controller 

Built-in input adaptive function

Constant Switching Frequency for Minimum Noise

±1% charge voltage accuracy

Automatic Recharge

Automatic Shutdown When Input Supply is Removed

Automatic Trickle Charging of Low Voltage

Stable with Ceramic Output Capacitor

Battery Temperature Sensing

ME4086 Applications（應用）：

Charging Docks 

Handheld InstrumenTEMP

Portable Computers

ME4086 Package（封裝形式）：

8-pin ESOP8

ME4086 Typical Application Circuit（典型應用電路）:

Note: 1.The dotted part of the box is the input capacitor. When the input voltage is lower than 9V, ceramic capacitor 

can be selected. When the input voltage is higher than 9V, an electrolytic capacitor over 100uF should be added into 

the input. The larger the charging power, the larger the capacity of electrolytic capacitor.

 2. For the hot-swappable application at the BAT pin, it is also necessary to add electrolytic capacitors, it is 

recommended to be 220uF or more.

Note: 1.The Rc and Cc value range of SW to GND, Rc: 0.5 Ω ~ 20 Ω, Cc: 1 nF ~ 100 nF.

 2. For the hot-swappable application at the BAT pin, it is also necessary to add electrolytic capacitors, it is 

recommended to be 220uF or more.

ME4086 Selection Guide(選購指南)：

product series	product description
ME4086ASPG	VFLOAT =4.2V(One-cell)
ME4086ESPG	VFLOAT =12.6V(Three-cell)

ME4086 Pin Configuration（引腳配置）：

ME4086 Pin Assignment（引腳分配）：

ME4086 Block Diagram（功能框圖）：